Results 1 to 4 of 4

Thread: Detailing - A quick "How To" Guide

  1. #1
    Administrator
    Join Date
    Jul 2013
    Location
    Swords, Dublin
    Posts
    3,189

    Detailing - A quick "How To" Guide





    Here's a quick "How To Guide" that I put together a few weeks back, as we're frequently asked about it!
    Decided to sticky it for all the Haus members - I feel it will be appreciated here!


    The process goes something along the lines of....

    Pre Wash/Snow Foam /De-grease (if doing a claying job)
    Wash
    Rinse
    De-Tar
    Rinse
    De-Ironise
    Rinse
    Clay
    Polish
    Protect

    Pre-Clean / Snow Foam

    The Aim
    To safely remove heavy dirt and grit, which ultimately reduces the chance of swirling. Very effective way of limiting / preventing the possible damage to the cars paintwork, by suspending dirt and grit in a lubricated solution that is easy to wash away. Also to soften any dirt that will not wash away when rinse step is complete.

    Products / Accessories
    Power Washer
    Snowfoam Lance / Pressurised Sprayer
    Snowfoam Solution
    Pre Clean
    APC
    De-greaser
    Detailing Brushes

    Methods
    1: Snowfoaming with Lance
    2: Pre Clean solution with Pressurised Sprayer

    How To
    1: Snowfoam Lance
    Add snowfoam solution to the lance bottle, topping up with warm water. See note #1
    Adjust the air mixture knob and the spray adjust knob to achieve a suitable spray to apply the snowfoam.
    Generally, starting at the highest point, spray on a reasonable thick solution of snowfoam, covering the entire car.
    Allow to dwell (see section Trims / Shuts / Door Jambs), until the solution has dripped away or it starts showing signs of drying out
    Rinse away with pressure washer, avoid direct contact with the paint, until initial heavy dirt is removed.
    Give the wheels / arches a gentle blast to remove heavy soiling.

    Note #1: If planning to strip back old LSP’s or claying, its no harm to add a moderate mixture or APC to help removal

    2. Pre Clean with Pressurised Sprayer
    Add Pre Clean solution to bottle and top up with water. Note #1 above applies here also.
    Pressurise the bottle and apply to car, concentrating on the lower half of the car where the dirt is heaviest.
    Allow to dwell (see section Trims / Shuts / Door Jambs), until the solution has dripped away or it starts showing signs of drying out.
    Rinse away with pressure washer, avoid direct contact with the paint, until initial heavy dirt is removed.
    Give the wheels / arches a gentle blast to remove heavy soiling.


    Wheels & Tyres / Arches

    The Aim
    To safely remove heavy dirt, grit, tar, iron particles from wheels.
    To ensure all surfaces are clean, to give a good surface for any protection to bond, ensuring the product will achieve its full potential.

    Products / Accessories
    Power Washer
    Wheel Cleaner w/ foam head trigger
    APC w/ foam head trigger
    Tar Remover
    De-Ironiser
    Wheel Brush
    Detailing Brushes
    Wheel Brace and Jack required if doing a full-on job! J
    Clay (optional)

    How To
    Give the wheel a gentle blast with the PW to remove the heavy dirt.
    Apply wheel cleaner through a foam head trigger (dilution ratio will depend on how heavily soiled the wheels are) and allow to dwell for a few seconds…rinsing with PW and wheel cleaner re-applied, may be necessary.
    Apply APC solution to the tyres and arches and allow to dwell.
    Using a combination of the wheel brush and detailing brushes, agitate the solution, trying to ensure the brushes get into all the nook and crannies.
    Agitate the APC solution on the tyres and arches with a detailing brushes.
    Rinse off with PW.
    Apply tar remover and allow to dwell – dwell time will vary from product to product.
    Rinse off with PW.
    Apply de-ironiser and allow to dwell – dwell time will vary from product to product.
    Rinse off with PW.
    The tar removing and de-ironising steps may need to be repeated.
    Using an old piece of clay is an optional step to give the wheels the best clean and surface for any LSPs to bond to.


    Trim / Shuts / Door Jambs

    The Aim
    To remove any dirt that has gathered in the nook and crannies from behind and around; trim, the shuts of the bonnet and boot lid, the door jambs, windows, badges, headlights, tail lights, side indicators, mirrors, vents and grilles, etc
    To ensure all surfaces are clean, as it’s the small details that make the difference between a detail and a valet / car wash

    Products / Accessories
    Power Washer
    APC w/ foam head trigger
    Detailing Brushes
    Microfiber Work Cloths

    How To
    Spray APC solution onto the affected area and agitate with various sized detailing brushes.
    Rinse away with PW.
    Open doors, bonnet and boot lid – get into all the tight spaces.
    Wipe away excess with Microfiber Cloths or if you are brave, rinse with the PW.
    This step can be completed during the Pre-Clean stage. While the snowfoam or pre-cleaner is dwelling on the car, proceed to clean the areas mentioned above. If this step has been completed before, often the snowfoam solution will be enough lubrication needed to gentle agitate the areas.


    Washing – The Two Bucket Method (2BM)

    The Aim
    To clean the paint work of general dirt and grime that is accumulated from day to day driving, including flies and bird etchings.
    To limit the potential damage (swirling) to the paint work

    Products / Accessories
    Two Buckets
    Grit Guard
    High quality Wash Mitt (Lambswool or Microfiber) – ideally two
    Well lubricated Shampoo

    How To
    Ensure that your Wash Mitt is thoroughly rinsed out and that the buckets are clean and free of any dirt or grit.
    Fill two large buckets with fresh water.
    At a grit guard to at least one of the buckets, ideally both.
    Add shampoo to one of the buckets (if using one grit guard, add it to the bucket without a GG).
    One bucket is now your “Rinse Bucket” (fresh water and GG) and the other is the “Wash Bucket” (shampoo and GG).
    Dip your Wash Mitt into the Wash Bucket and starting at the roof, wash one half of the roof (a section)
    Once you have finished a section, rinse out your Wash Mitt in the Rinse Bucket. Then dip it into the Wash Bucket, collecting clean water and shampoo. This ensures that any potentially harmful grit that has been picked up by the wash mitt, is now in the Rinse Bucket. The Girt Guard, ensures that each time you rinse your wash mitt, you don’t pick up harmful grit that you have previously wash out. This is down to two reasons. Firstly the GG prevents you dipping the wash mitt to the bottom of the bucket where the grit is, and re-contaminating your wash mitt. Secondly as the GG is sectioned, it prevents grit being lifted from the bottom of the bucket by the whirlpool that is created when you rinse out your wash mitt.
    Continue this process of washing one section (a panel) from highest to lowest, rinsing the mitt in the rinse bucket, then dipping it into the wash bucket, and washing a section. It is advisable to use one mitt for the top of half of the car (least dirty and most obvious place to notice swirls) and a second for the lower half (below the rub trim level).
    Once all panels have been clean, give the whole car a good rinse down with the PW, ensure that all the trim and shuts are free from shampoo and perhaps snowfoam also.


    Paint Prep including De-Tarring, De-Ironising and Claying

    The Aim
    To decontaminate the paint work of bonded contaminants (microscopic), accumulated from subjected to many miles of driving and general environmental surroundings that regular washing wont remove; including tar, iron particles, over-spray, tree spa, light paint or rubber/plastic transfer, etc
    To give the best surface for LSP to bond to, ensuring good appearance and durability of the product.

    Products / Accessories
    Power Washer
    Tar Remover
    De-Ironiser
    Clay & Lubricant

    How To
    Apply tar remover to affected areas, being careful around plastic / rubber trim.
    Allow to dwell and rinse off with PW. Repeat if necessary. Ideally you should not have to touch the tar, but sometimes a light wipe may be necessary.
    Apply the de-ironiser.
    Allow to dwell. Shortly after application the solution, in places, will turn purple and begin to bleed; these areas are affected by iron particles. Spreading with a sponge or clean microfiber is OK as the paintwork should be free of any dirt or grit that could be dragged across the paint resulting in damage.
    Allow to dwell and rinse off with PW. Repeat if necessary.
    At this point the paint work should be free of any potentially damaging contamination resulting from claying.
    Knead the clay into a manageable flat section
    Starting at the roof, spray on a generous amount of lubricant to an approximate 1ft * 1ft section. Gently rub the clay back and forth on the paint work. At first the clay will not slide smoothly over the paint work (as its contaminated). Continued moving the clay back and forth and after a few seconds the clay will slide much freer, more like its on ice. At this point that section of paintwork has been de-contaminated and another section can be started, not forgetting to use plenty of lubricant. If you come across a section that the clay is very grabby on, be sure to use more lubricant and less pressure on the clay, and eventually it will slide freely.
    Once all the paintwork has been clayed, the whole car should be re-washed and dried. NOW, your paintwork is clean!!

    Up to this point is considered “preparation”; and the paintwork is prepared for any or all of the following steps…
    Polishing (hand or machine)
    Glazing
    LSP


    Polishing (by hand)

    The Aim

    To remove oxidisation
    Add depth to the paint and gloss to the paint
    Remove / hide light swirling

    Products / Accessories
    Polish
    Applicator Pad
    High quality Buffing Microfiber Cloth

    How To
    Prime the applicator with a generous amount of polish.
    Apply to the paintwork with reasonable pressure, working it in various directions, try to apply it evenly.
    When the spread of the product appears to be diminishing, apply a small amount to the applicator and continue.
    Allow the polish to dry to a haze and buff of with a high quality buffing microfiber cloth. Depending on the polish, it may be best to apply one or two panels at a time and then buffing off, before continuing with other panels.
    Depending on the desired finish, multiple stages may be required

    Glazing

    The Aim

    To add a glossy wet look to the paint
    To hide light swirling

    Products / Accessories
    Glaze
    Applicator Pad
    High quality Buffing Microfiber Cloth

    How To
    Same as hand polishing...
    Prime the applicator with a generous amount of glaze.
    Apply to the paintwork with reasonable pressure, working it in various directions, try to apply it evenly.
    When the spread of the product appears to be diminishing, apply a small amount to the applicator and continue.
    Allow the glaze to dry to a haze and buff of with a high quality buffing microfiber cloth. Depending on the glaze, it may be best to apply one or two panels at a time and then buffing off, before continuing with other panels.
    Usually one coat of glaze is enough...maximum two!
    Glazing usually diminishes the effectiveness of the LSP... you will probably find that you are very disappointed in the performance of the LSP, this is down to the fact that the glaze is preventing a good bond. Durability suffers for the wet look.

    LSP (Last Stage Protection) – Wax / Sealant / Nano Technology

    The Aim

    To protect the paint work.
    To add a glossy wet look to the paint
    Beading J

    Products / Accessories
    LSP of choice
    Applicator Pad / Applicator Microfiber Cloth
    High quality Buffing Microfiber Cloth

    How To
    Much the same as hand polishing and glazing...
    Prime the applicator with a generous amount of LSP.
    Apply to the paintwork with reasonable pressure, working it in various directions, try to apply it evenly. The secret to easy applying and removal of LSP is to keep to applying thin coats, but multiple times – its much better for durability and easy on / easy off than applying one very thick coat.
    When the spread of the product appears to be diminishing, apply a small amount to the applicator and continue.
    Allow the LSP to dry to a haze and buff of with a high quality buffing microfiber cloth. Depending on the LSP, it may be best to apply one or two panels at a time and then buffing off, before continuing with other panels.
    The more coats applied the better...minimum two, too ensure full coverage and durability. Applying more coats usually results in a deeper and glossier shine, so advantages are twofold with durability.

  2. #2
    Administrator
    Join Date
    Jul 2013
    Location
    Swords, Dublin
    Posts
    3,189

    RE: Detailing - A quick

    Updated April 2016 - Due to new products that we carry, we've made a few tweaks to our recommended line up!


    Here are a list of products that I would recommend....
    Some may seem expensive, but they are high quality and will be durable or a little will go a long way!

    There are of course other options that will work, these are my personal favourites!

    Pre Wash - 50Cal Frontline Pre Wash
    Bilt Hamber Surfex HD

    Shampoo - Bilt Hamber's Auto Wash
    50Cal Tracer

    Wash Mitt - Microfiber Madness Incredimitt
    CarPro Merino Wool Mitt
    Bilt Hamber Auto Mitt

    Grit Guard - Scratch Shields

    Wheels - Bilt Hamber Auto Wheel
    50Cal Retaliate


    Drying Towel - Microfiber Madness Dry Me Crazy
    CarPro Fat Boa

    De-Tar - CarPro TarX

    De-Iron - CarPro IronX
    Bilt Hamber Korrosol

    Clay - Bilt Hamber Auto Clay
    Autobrite's Clay

    Hand Polish - CG's P40 Pro Polish

    Machine Polish - there are so many good options, and what works for one person, may not be agreeable to another - its finding what works for you and your technique.

    Protection - depends on what you are looking for....ask about it here

    Buffing Cloth - Microfiber Madness Crazy Pile

    Applicators - CG's UFO
    Last edited by Curran; 14-04-16 at 17:11.

  3. #3

    RE: Detailing - A quick "How To" Guide

    This should be a sticky ; )

  4. #4
    Administrator
    Join Date
    Jul 2013
    Location
    Swords, Dublin
    Posts
    3,189

    RE: Detailing - A quick "How To" Guide

    Quote Originally Posted by COUPE ///M
    This should be a sticky ; )
    Good man Ger!

    It is...we call them 'important threads' and has been since I posted it!! :P

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •